Accord Archives

Podcast Episode #26 – 2006-2007 Honda Accord Splash Guard Installation

Splash guards are very important for any vehicle. Honda’s Genuine splash guards are custom-fitted in the wheel wells to blend in with the vehicle design. No drilling is required to install. They are manufactured from injection-molded thermoplastic which will provide superior strength and durability, whatever the outside temperature. The featured musical artist for this podcast is Flux.



Podcast Episode #24 – 2006-2007 Honda Accord Spoiler Installation

In this episode you will see the procedures for installing a spoiler on an 06-07 Accord. The video shows the required steps on the left side of the vehicle. Simply perform the same work on the right side of the trunk lid to complete the installation. Please refer to our accessory store for a PDF version of the Honda instructions.



2003-2005 Honda Accord Keyless Entry Programming

NOTES:
• The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased.
• Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must
reprogram all of the transmitters once you are in the programming mode.
• You must complete steps 1–6 within 4 seconds of the previous step to keep the system from exiting the programming mode.

Programming the Transmitter

1. Turn the ignition switch to ON (II).
2. Press the “Lock” or “Unlock” button on one of the transmitters. (An unprogrammed transmitter can be used for this step.)
3. Turn the ignition switch to LOCK (0).
4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2.
5. Turn the ignition switch to ON (II).
6. Press the “Lock” or “Unlock” button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode.
7. Within 10 seconds, press the “Lock” or “Unlock” button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the
transmitter’s code.
8. Turn the ignition switch to LOCK (0) to exit the
programming mode.

Ordering a Transmitter
You may order direct from College Hills Honda.  Simply call 1-888-244-6632 and ask for Internet Parts.

Batteries for the Transmitter
The battery number is CR2025. Each transmitter uses one battery.



1998-2002 Honda Accord EX & SE Keyless Entry Programming

NOTES:
• The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased.
• Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must
reprogram all of the transmitters once you are in the programming mode.
• You must complete steps 1–6 within 4 seconds of the previous step to keep the system from exiting the programming mode.

Programming the Transmitter

1. Turn the ignition switch to ON (II).
2. Press the “Lock” or “Unlock” button on one of the transmitters. (An unprogrammed transmitter can be used for this step.)
3. Turn the ignition switch to LOCK (0).
4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2.
5. Turn the ignition switch to ON (II).
6. Press the “Lock” or “Unlock” button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode.
7. Within 10 seconds, press the “Lock” or “Unlock” button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitter’s code.
8. Turn the ignition switch to LOCK (0) to exit the programming mode.

Ordering a Transmitter
You may order direct from College Hills Honda.  Simply call 1-888-244-6632 and ask for Internet Parts.

Batteries for the Transmitter
The battery number is CR2025. Each transmitter uses one battery.



1996-2002 Accord Keyless Entry Programming

NOTES:
• The system accepts up to three transmitters. The transmitter codes are stored in a stacking-type memory. If a fourth transmitter code is programmed, the code for the first transmitter is erased.
• Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode.
• You must complete steps 1–6 within 4 seconds of the previous step to keep the system from exiting the programming mode.

Programming the Transmitter

1. Turn the ignition switch to ON (II).
2. Press the “Lock” or “Unlock” button on one of the transmitters. (An unprogrammed transmitter can be used for this step.)
3. Turn the ignition switch to LOCK (0).
4. Repeat steps 1, 2, and 3 two more times using the same transmitter used in step 2.
5. Turn the ignition switch to ON (II).
6. Press the “Lock” or “Unlock” button on the same transmitter. Make sure the power door locks cycle to confirm that the system is in programming mode.
7. Within 10 seconds, press the “Lock” or “Unlock” button on each transmitter. Make sure the power door locks cycle after you press each transmitter button to confirm that the system accepted the transmitter’s code.
8. Turn the ignition switch to LOCK (0) to exit the programming mode.

Ordering a Transmitter
You may order direct from College Hills Honda.  Simply call 1-888-244-6632 and ask for Internet Parts.

Batteries for the Transmitter
The battery number is CR2025. Each transmitter uses one battery.